Choosing The Right Grinding Wheel(2)
Hard, brittle materials generally require a wheel with a fine grit size and a softer grade. Hard materials resist the penetration of abrasive grains and cause them to dull quickly. Therefore, the combination of finer grit and softer grade lets abrasive grains break away as they become dull, exposing fresh, sharp cutting points. On the other hand, wheels with the coarse grit and hard grade should be chosen for materials that are soft, ductile and easily penetrated.
The amount of stock to be removed is also a consideration. Coarser grits give rapid stock removal since they are capable of greater penetration and heavier cuts. However, if the work material is hard to penetrate, a slightly finer grit wheel will cut faster since there are more cutting points to do the work.
Wheels with vitrified bonds provide fast cutting. Resin, rubber or shellac bonds should be chosen if a smaller amount of stock is to be removed, or if the finish requirements are higher.
Another factor that affects the choice of wheel bond is the wheel speed in operation. Usually vitrified wheels are used at speeds less than 6,500 surface feet per minute. At higher speeds, the vitrified bond may break. Organic bond wheels are generally the choice between 6,500 and 9,500 surface feet per minute. Working at higher speeds usually requires specially designed wheels for high speed grinding.
In any case, do not exceed the safe operating speed shown on the wheel or its blotter. This might be specified in either rpm or sfm.
The next factor to consider is the area of grinding contact between the wheel and the workpiece. For a broad area of contact, use a wheel with coarser grit and softer grade. This ensures a free, cool cutting action under the heavier load imposed by the size of the surface to be ground. Smaller areas of grinding contact require wheels with finer grits and harder grades to withstand the greater unit pressure.
Next, consider the severity of the grinding action. This is defined as the pressure under which the grinding wheel and the workpiece are brought and held together. Some abrasives have been designed to withstand severe grinding conditions when grinding steel and steel alloys.
Grinding machine horsepower must also be considered. In general, harder grade wheels should be used on machines with higher horsepower. If horsepower is less than wheel diameter, a softer grade wheel should be used. If horsepower is greater than wheel diameter, choose a harder grade wheel.
Care And Feeding
Grinding wheels must be handled, mounted and used with the right amount of precaution and protection.
They should always be stored so they are protected from banging and gouging. The storage room should not be subjected to extreme variations in temperature and humidity because these can damage the bonds in some wheels.
Immediately after unpacking, all new wheels should be closely inspected to be sure they have not been damaged in transit. All used wheels returned to the storage room should also be inspected.
Wheels should be handled carefully to avoid dropping and bumping, since this may lead to damage or cracks. Wheels should be carried to the job, not rolled. If the wheel is too heavy to be carried safely by hand, use a hand truck, wagon or forklift truck with cushioning provided to avoid damage.
Before mounting a vitrified wheel, ring test it as explained in the American National Standards Institute's B7.1 Safety Code for the Use, Care and Protection of Grinding Wheels. The ring test is designed to detect any cracks in a wheel. Never use a cracked wheel.
A wise precaution is to be sure the spindle rpm of the machine you're using doesn't exceed the maximum safe speed of the grinding wheel.
Always use a wheel with a center hole size that fits snugly yet freely on the spindle without forcing it. Never attempt to alter the center hole. Use a matched pair of clean, recessed flanges at least one-third the diameter of the wheel. Flange bearing surfaces must be flat and free of any burrs or dirt buildup.
Tighten the spindle nut only enough to hold the wheel firmly without over-tightening. If mounting a directional wheel, look for the arrow marked on the wheel itself and be sure it points in the direction of spindle rotation.
Always make sure that all wheel and machine guards are in place, and that all covers are tightly closed before operating the machine. After the wheel is securely mounted and the guards are in place, turn on the machine, step back out of the way and let it run for at least one minute at operating speed before starting to grind.